I. Automatinis litavimas spausdinimas mašina valymas
Visas automatinis litavimas pasta spausdinimas mašina is naudotas in sausas valymas, šlapias valymas ir vakuumas valymas iš šie trys būdai, automatinis lydmetalis pasta spausdinimas mašina to take up the role of automatic cleaning trafaretas, to užtikrinti the role of printing quality. With the development of SMT, small gap, fast speed, PCB on the many pull the tip, even tin and cleaning have a lot to do with the valymas funkcija gali būti ištobulinta to realizuoti the speed that the production of high efficiency.
Automatic solder paste printing machine image positioning depends on the positioning algorithm, positioning algorithm is also one of the core algorithms of automatic solder paste printing machine. With the PCB board production efficiency is getting higher and higher, the electronic components on the board is getting smaller and smaller, the positioning accuracy and speed also put forward higher requirements. Currently, the positioning algorithms of most automatic solder paste printers on the market are based on image gray scale and realized by autocorrelation matching. For copper-plated boards with good surface uniformity, the grayscale algorithm can complete the function of automatic positioning very well. However, the emergence of more and more tin-plated boards, gold-plated boards, and flexible PCB boards has brought great challenges to grayscale localization. Because the surface uniformity of tin-plated, gold-plated boards is not very good, the reflection rate is high, so that the Mark points on the PCB board has a great difference in the brightness of the imaging, increasing the false detection rate of grayscale localization and the rate of missed detection. Flexible board due to the surface flatness is not good, PCB Mark points on the imaging will also have a large difference in brightness, but also make the Mark point size, shape changes, these problems are based on grayscale positioning algorithms are difficult to overcome. Geometry-based positioning algorithms can be well adapted to appeal to these issues.
III. sveikas alavas įklijavimas spausdinimas įrenginys atsegimas režimas
Geras arba blogas Snap-off tiesiogiai paveikia the printing effect, the general full automatic solder paste printing machine has two ways of Snap-off
1. "first up scraper after Snap-off", the use of more common, mainly more simple PCB board.
2. "First take off the mold after the scraper", the use of thin PCB boards and so on.
Lydmetalis pasta spausdinimas mašina skirtingi tipai PCB pelėsis išleidimas reikalavimai specialiai suprojektuoti trys rūšys pelėsiai išleidimas režimas 2c taikoma skirtingi alavas reikalavimai
a. Start grandiklis pirmas ir tada Snap-off.
b. Pirma laida the mold after starting the squeegee.
c. "Squeegee detach first, keep the pre-pressure value, then release the mold".
Apibūdinimas
Transmisija režimas sekcijos tipas takelis
PCB spaustukas režimas
Programinė įranga reguliuojamas slėgis elastinis šonas slėgis
Specifikacijos
| Produktas pavadinimas | ND1 visas automatinis vaizdas spausdintuvas | Lenta marža tarpas | 20 mm |
| Maksimalus lentos dydis (X x Y) | 450mm x 350 mm | Perdavimas aukštis nuo the ground | 900±40mm |
| Minimalus lentos dydis (X x Y) | 50mm x 50mm | Perdavimas greitis | 1500mm/s(Max) |
| PCB storis | 0.6mm~14mm | Perdavimas orbita kryptis | L-R, R-L, L-L, R-R |
| Metmenys | 1% įstrižainė | Mašina svoris | Appro. 1000Kg |
| Maksimalus lenta svoris | 10 kg | Konfigūracija iki 3 mm |